Product Name:  High Temperature Spindle Grease

Manufacturer:  Fluoramics Inc.
Address:  18 Industrial Avenue, Mahwah, N.J.  07430

Emergency Phone:  201-825-8110 
Information Phone:  1-800-922-0075
Fax Number:  201-825-7035

Product use:  Grease for high speed rotating machinery
 

Flash Point & Method Used:  ASTM D 92
Flammability Limits in Air % by Volume:  N/A
Extinguisher Media:  Carbon Dioxide - Dry Chemical
Special Fire Fighting Procedures:  Use foam and water.  Spray carefully to prevent excessive frothing.  Cool exposed containers with water.
Unusual fire and Explosion Hazards:  Do not store or mix with strong oxidants.

Stability:  Stable
Conditions to Avoid:  Excessive heat - direct flame
Incompatability (Materials to Avoid):  Strong oxidants, ie Liquid Chlorine or Concentrated Oxygen
Hazardous Decomposition Products:  CO²  - Trace quantities of fluorides. Decompose product above 500º F
Hazardous Polymerization:  Will not occur

Primary Routes of Entry:  Inhalation, skin, ingestion
Health Hazards: 
Signs and Symptoms of Exposure:  Prolonged & repeated over-exposure may irritate the skin or some individuals.
Medical Conditions Generally Aggravated by Exposure:  See below.
Eye Contact:  Wash with copious amounts of water.
Skin Contact:  Remove by wiping and wash with soap and water.
Inhalation:  Expose to fresh air.
Ingestion:  Treat symptomatically.  Call physician.
Emergency First Aid Procedures:  Seek medical assistance for further treatment, observation and support if necessary.

Respiratory Protection (Specify Type):  None required at ambient temperature.
Protective Gloves:  Butyl rubber
Eye Protection:  Safety goggles
Ventilation to be Used:  Local exhaust (preferred),  Mechanical (general); usually none.
Other Protective Clothing and Equipment:  Protective garment when applicable.
Hygienic Work Practices:  As indicated.

Steps to be Taken if Material is Spilled or Released:  Absorb with porous inert material.  Transfer to closed container.  Floor may be slippery.  Use car to avoid falls.
Waste Disposal Methods:  Sealed drum containment as per organic chemicals.  Follow federal, state and local regulations regarding health and pollution.
Precautions to be Taken in Handling and Storage:  Keep containers closed when not in use.  Avoid excessive heat or direct flane.
Other Precautions and/or Special Hazards:  Avoid frequent or prolonged skin contact or inhalation of fumes, mists and vapors.

U.S.  (49 CFR):  Proper Shipping Name:  Non-Hazardous Material
IATA:  Proper Shipping Name:  Non-Dangerous Goods
IMDG:  Proper Shipping Name:  Non-Dangerous Goods

Physical Properties:

Appearance:  Greenish blue
Odor:  Mild petroleum odor
Physical state:  Liquid
pH as supplied
Boiling Point:  N/A
Melting Point:  N/A
Freezing Point:  N/A
Vapor Pressure (mmHg):  Nil
Vapor Density (air=1):  N/A
Specific Gravity (H20=1):  9050
Evaporation rate:  N/A
Solubility in water:  Insoluble in cold water

Stability:  Stable
Conditions to avoid:  Temperatures above 250F without adequate ventilation.  Will not polymerize
Incompatibility (Material to Avoid):  Strong acids, bases and oxidizing agents
Hazardous decomposition or by-products:  Carbon dioxide, carbon monoxide, unburned hydrocarbons and traces of sulfer, phosphorus or nitrogen, PTFE Decomposition product.
 

No toxicology data available

Do not allow to enter soil, waterways or wastewater

Waste Disposal Method:  Follow all local, state and federal regulations 
RCRA Hazard Class:  Determine if this material is a RCRA Hazardous Waste at the time of disposal

Transportation Information:  N/A

Non-hazardous product
U.S. Federal Regulations:  TSCA (Toxic Substance Control Act):
The components of this product are listed
SARA Title III (Superfund Amendments and Reauthorization Act):
311/312 Hazard Categories:  No Hazard categories identified

Date prepared:  May 2, 2006