MATERIAL SAFETY DATA SHEET

IDENTITY:  INDUSTRIAL TUFOIL

 
SECTION 1 - PRODUCT & COMPANY IDENTIFICATION

Product Name:  Industrial Tufoil

Manufacturer:  Fluoramics Inc.
Address:  18 Industrial Avenue, Mahwah, N.J.  07430

Emergency Phone:  201-825-8110 
Information Phone:  1-800-922-0075
Fax Number:  201-825-7035

Product use:  Lubricant
                             

 
SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS
This material is not classified as hazardous under OSHA regulations.
 COMPONENTS
CAS #
Weight %
ACGIH - TLV-TWA
Petroleum Hydrocarbon Motor Oil
64741-88-4
35-40
5mg/m3
Methacrylate/Vinyl Pyrrolidine Copolymer
68171-46-0
25-30
N/A
Polyalpha olefin
68649-12-7
10-20
N/A
Didecyl adipate Dimer Ester
16958-92-2
5-10
N/A
Molybdenum Di (2-ethyl) Phosphordithlioate
72030-25-2
5-10
N/A
Polytetrafluoroethylene
9002-84-0
1-5
N/A

 
SECTION 3 - PHYSICAL/CHEMICAL CHARACTERISTICS
  Boiling point:  300º F Overpoint
Vapor Pressure:  Nil
Vapor Density:  N/A
Solubility in Water:  Nil
Physical State at Room Temperature - Liquid
Specific Gravity:  9047
Melting Point:  N/A
Evaporation Rate (Butyl Acetate 1):  N/A
Water Reactive:  N/A
Appearance and Odor:  Reddish tan - odorless

 
SECTION 4 - FIRE & EXPLOSION HAZARD DATA

Flash Point & Method Used:  435º F - ASTM D 92
Flammability Limits in Air % by Volume:  N/A
Extinguisher Media:  Carbon Dioxide - Dry Chemical
Special Fire Fighting Procedures:  Use foam and water.  Spray carefully to prevent excessive frothing.  Cool exposed containers with water.
Unusual fire and Explosion Hazards:  Do not store or mix with strong oxidants.

 
.
NFPA CODES
HMIS CODES
HEALTH
1
1
FLAMMABILITY
1
1
REACTIVITY
0
0
PERSONAL PROTECTION  
B

 
SECTION 5 - REACTIVITY HAZARD DATA

Stability:  Stable
Conditions to Avoid:  Excessive heat - direct flame
Incompatability (Materials to Avoid):  Strong oxidants, ie Liquid Chlorine or Concentrated Oxygen
Hazardous Decomposition Products:  CO2  - Trace quantities of fluorides. Decompose product above 500º F
Hazardous Polymerization:  Will not occur

 .

 
SECTION 6 - HEALTH HAZARD DATA

Primary Routes of Entry:  Inhalation, skin absorption, ingestion
Carcinogen listed in:  N/A
Health Hazards:  Acute - treat symptomatically
Signs and Symptoms of Exposure:  Prolonged & repeated over-exposure may irritate the skin or some individuals.
Medical Conditions Generally Aggravated by Exposure:  See below.
Eye Contact:  Wash with copious amounts of water.
Skin Contact:  Remove by wiping and wash with soap and water.
Inhalation:  Expose to fresh air.
Ingestion:  Treat symptomatically.  Call physician.
Emergency First Aid Procedures:  Seek medical assistance for further treatment, observation and support if necessary.

 
SECTION 7 - CONTROL AND PROTECTIVE MEASURES

Respiratory Protection (Specify Type):  None required at ambient temperature.
Protective Gloves:  Butyle rubber
Eye Protection:  Safety goggles
Ventilation to be Used:  Local exhaust (preferred), Mechanical (general); usually none.
Other Protective Clothing and Equipment:  Protective garment when applicable.
Hygienic Work Practices:  As indicated.

 
SECTION 8
PRECAUTIONS FOR SAFE HANDLING AND USE
LEAK PROCEDURES

Steps to be Taken if Material is Spilled or Released:  Absorb with porous inert material.  Transfer to closed container.
Waste Disposal Methods:  Sealed drum containment as per organic chemicals.  Follow federal, state and local regulations regarding health and pollution.
Precautions to be Taken in Handling and Storage:  Keep containers closed when not in use.
Other Precautions and/or Special Hazards:  Avoid frequent or prolonged skin contact or inhalation of fumes, mists and vapors.

 
 
SECTION 9
PHYSICAL & CHEMICAL PROPERTIES / DANGEROUS GOODS SHIPPING REGULATIONS

                                       U.S.  (49 CFR):  Proper Shipping Name:  Non-Hazardous Material

                                                      IATA:  Proper Shipping Name:  Non-Dangerous Goods

                                                    IMDG:  Proper Shipping Name:  Non-Dangerous Goods

Physical Properties:

Appearance:  Translucent tan
Odor:  Mild petroleum odor
Physical state:  Liquid
pH as supplied
Boiling Point:  N/A
Melting Point:  N/A
Freezing Point:  N/A
Vapor Pressure (mmHg):  Nil
Vapor Density (air=1):  N/A
Specific Gravity (H20=1):  9050
Evaporation rate:  N/A
Solubility in water:  Insoluble in cold water

 
SECTION 10:  STABILITY & REACTIVITY

Stability:  Stable
Conditions to avoid:  Temperatures above 250F without adequate ventilation.  Will not polymerize
Incompatibility (Material to Avoid):  Strong acids, bases and oxidizing agents
Hazardous decomposition or by-products:  Carbon dioxide, carbon monoxide, unburned hydrocarbons and traces of sulfer, phosphorus or nitrogen, PTFE Decomposition product.
 

 
SECTION 11:  TOXICOLOGICAL INFORMATION

No toxicology data available

 
SECTION 12:  ECOLOGICAL INFORMATION

Do not allow to enter soil, waterways or wastewater

 
SECTION 13:  DISPOSAL CONSIDERATIONS

Waste Disposal Method:  Follow all local, state and federal regulations 
RCRA Hazard Class:  Determine if this material is a RCRA Hazardous Waste at the time of disposal

 
SECTION 14:  TRANSPORTATION INFORMATION

Transportation Information:  N/A

 
SECTION 15:  REGULATORY INFORMATION

Non-hazardous product
U.S. Federal Regulations:  TSCA (Toxic Substance Control Act):
The components of this product are listed
SARA Title III (Superfund Amendments and Reauthorization Act):
311/312 Hazard Categories:  No Hazard categories identified

 
SECTION 16:  OTHER INFORMATION

Date prepared:  March 20, 2006